The phrase "fire rated" usually stands in for one of two entirely different properties, and buyers compare them as if they were interchangeable.
The first is a use class. EN ISO 10874 grades flooring by traffic: 21 to 23 domestic, 31 to 34 commercial, 41 to 43 light industrial. A class 33 floor is a heavy commercial floor. It says nothing about fire.
The second is a reaction-to-fire classification, written in a form like Bfl-s1. That describes how the material behaves when exposed to a flame or a radiant heat source. It says nothing about wear.
A quotation offering "class 33, fire rated" is not wrong, but it is not a specification either. Ask which class applies to which property and for the document behind each. On the traffic side, the comparison in our wear layer guide is the place to start; on the fire side, the rest of this article.
Within the European Union, reaction to fire is classified under EN 13501-1, which replaced the older national systems with a common set of labels. Flooring classes carry the subscript fl, and are then qualified by two more letters.
The first extra letter is smoke production: s1 is the lowest band, s2 intermediate, s3 the highest. The second is burning droplets and particles: d0, d1, d2, from best to worst. Bfl-s1 therefore means class B reaction to fire, a flooring product, with low smoke production.
The tests behind those letters are specific and worth knowing by name, because they appear on the report you will be asked to check. Flooring is normally assessed with EN ISO 9239-1, a radiant panel test that measures critical heat flux, and EN ISO 11925-2, a small-flame test. Classes A1 and A2 additionally require EN ISO 1182 and EN ISO 1716 for non-combustibility and calorific value.
| Class | Contribution to fire | Test basis | How it appears in specifications |
|---|---|---|---|
| A1 | None | EN ISO 1182 and 1716 | Mineral surfaces; not typical of resilient flooring |
| A2 | Very limited | The above plus 9239-1 and 11925-2 | Occasionally written for high-risk areas |
| B | Very limited | EN ISO 9239-1 and 11925-2 | Commonly the target for commercial resilient floors |
| C | Limited | Same | Appears in older or secondary-room specifications |
| D | Medium | Same | Rarely acceptable for commercial work |
| E | High | EN ISO 11925-2 only | Below what most commercial specifications accept |
| F | Not determined | No test | No declaration exists |
The class and the smoke band are separate requirements. A Bfl-s2 product and a Bfl-s1 product can both be described as class B, and a specification that names only the class has left the smoke question open.
Outside the EU the same floor may be assessed against a different method, and projects in the Middle East frequently name the American one.
- ASTM E648, also published as NFPA 253. A critical radiant flux test for flooring. Class I requires a critical flux of 0.45 W/cm² or higher, Class II 0.22 W/cm² or higher. Gulf specifications commonly ask for Class I.
- BS 476 parts 6 and 7. The older British route, still written into some specifications and legacy projects.
- National codes. Projects in the UAE and Saudi Arabia often reference a building code plus a civil defence requirement, so the same floor may need two separate documents.
There is no conversion table between Euroclass and ASTM classes. The two methods measure different behaviour on different apparatus, so a supplier who offers "Bfl-s1, equivalent to Class I" is improvising. If the specification names ASTM E648, ask for an ASTM E648 report.
Inside Europe there is a second layer of paperwork. Resilient floor coverings fall under EN 14041, and the manufacturer must issue a Declaration of Performance under the Construction Products Regulation. The DoP names the reaction-to-fire class for the product, and the classification report is the evidence behind it. A DoP without a report is a claim; a report without a DoP is an incomplete file.
A fire classification attaches to a construction, not to a brand. That single sentence explains most of the arguments that happen at the quotation stage.
The tested assembly normally includes the total thickness, the wear layer, and the backing — an attached IXPE or EVA layer is part of the product that burned. If the floor is glue-down, the adhesive may also be part of the tested assembly, which means changing the adhesive changes the result. And the test is run on a defined substrate, usually a mineral board, so the classification describes a floor on that substrate.
The practical consequences are narrow and specific. A report for a bare plank does not cover the same plank with a foam backing laminated to it. A family report covering several thicknesses is only evidence for the thicknesses it lists, in a construction table that the report should contain. A classification obtained on one substrate does not automatically transfer to a raised access floor or a timber deck, and a project that specifies a different substrate may need the question put to the specifier rather than to the supplier.
This is also where a range becomes complicated for the buyer. A supplier with five thicknesses, two backings and three adhesive options has a matrix, not a product, and the fire file has to cover the cell you are ordering. The construction options in a rigid core range, for comparison, are set out on our SPC rigid core page.
Ten minutes with the document answers most of it. Work through these in order.
- Confirm what the document is. A classification report issued by a notified body is what a specifier wants. An internal test report showing a result is not the same document, and neither is a certificate of conformity issued by the supplier.
- Check the laboratory and its accreditation. The body should be identifiable and, for a European classification, notified for the relevant test.
- Read the construction table. Thickness, wear layer, backing, adhesive, substrate. Compare it with the line item you are buying, not with the product family name.
- Check the name on the report. Reports are often held by a trading company or another factory. That is not automatically disqualifying, but it is a question to ask rather than a detail to overlook.
- Check the standard edition and date. EN 13501-1 has been revised; a classification to a superseded edition may still be valid but should be explained.
- Check the smoke and droplet bands, not just the main class, if the specification names them.
- Match the report to the DoP and the CE marking, so the class on the label is the class in the report.
- Keep batch traceability. If the file is going to be checked on site, the production batch should be identifiable from the shipping documents.
A supplier who cannot produce the report has answered the question as clearly as one who can, just not in the way the buyer hoped. Finding that out before the deposit is the point of asking.
Is Bfl-s1 the same as class 33?
No. Class 33 is a use class under EN ISO 10874, describing heavy commercial traffic and nothing else. Bfl-s1 is a reaction-to-fire classification under EN 13501-1. A product can be class 33 and Cfl-s1, or class 23 and Bfl-s1, and the two numbers answer different questions. Specifications that list only one of them are incomplete.
Can one report cover an entire product range?
Sometimes, but only if the classification report says so. Extended application rules allow a tested construction to cover related thicknesses and variants, and reputable reports list exactly which ones. A single report for one thickness does not silently extend to a thicker product with a different backing. Ask for the construction table and match it to the order line.
Does a residential project need a fire classification?
It depends on the building code and the room, not on the product. In many European markets the requirement bites in common areas, escape routes and multi-storey buildings rather than in a single dwelling. The right sequence is to ask the specifier which class is required and for which areas, then ask the supplier for the document that matches. Guessing produces either an unnecessary file or a missing one.
Need the fire file checked for a project?
Send the required class, the areas, the substrate and the destination market, and we will confirm which documents exist for the construction you are considering before production is committed.
Request a B2B Quote ↗