European specifications for vinyl flooring draw on three unrelated test methods, and none of them converts into the others.
R classes come from a ramp test in which an operator wearing safety shoes walks up an oil-covered incline until they slip. A, B and C classes come from a similar ramp, barefoot, with a soap solution. PTV or SRV comes from a pendulum device swung across a wet surface.
The commercial consequence is simple and often missed: a floor specified from an R class alone has been specified for shod traffic on an oily surface. A hospital bathroom, a swimming pool surround or a spa changing room is a barefoot, wet, soapy environment. The R number does not describe it.
The four methods below cover almost every slip specification a buyer will meet. The contaminant and the footwear are the parts that decide whether a given test is relevant to a given room.
| Method | Standard | Footwear and contaminant | Output | Used for |
|---|---|---|---|---|
| Ramp, shod | DIN 51130 | Safety shoes on motor oil | R9 to R13 | Industrial floors, commercial kitchens, ramps |
| Ramp, barefoot | DIN 51097 | Bare feet on soap solution | A, B, C | Pools, showers, changing rooms, wet rooms |
| Pendulum | EN 13036-4, and BS 7976 in the UK | Rubber slider on a wet surface | PTV or SRV | Entrances, retail, public circulation |
| Surface roughness | EN ISO 4287 | Dry profile measurement | Rz in micrometres | Wet barefoot areas, as a supporting measure |
Two details decide whether a number is usable at all. On the pendulum, the rubber slider is either the 4S compound or the CEN compound, and the two produce different values on the same floor; a result that does not name the slider cannot be compared. On the ramp, the test is run with the contaminant named in the standard, so an R class is an oily result by definition, not a clean-water one.
The bands are worth knowing by heart, because a specification that says only "R11" or "class C" hides a range.
- R classes: R9 covers about 6° to 10° of ramp angle, R10 above 10° to 19°, R11 above 19° to 27°, R12 above 27° to 35°, and R13 above 35°. R11 therefore spans eight degrees, which is why two floors both labelled R11 can feel very different underfoot.
- Barefoot classes: A covers 12° to 18°, B 18° to 24°, and C above 24°. A pool surround is commonly specified at B or C; a domestic bathroom is not necessarily any of them.
- Pendulum: UK guidance treats a wet PTV of 36 or above as low slip risk for level walking, 25 to 35 as moderate, and below 25 as high. Those thresholds are quoted for the 4S slider and do not apply to results produced with the CEN slider.
- Roughness: guidance for wet barefoot areas often cites a mean roughness depth of at least 10 micrometres as a supporting criterion, measured on the profile rather than estimated by touch.
Higher is not automatically better. R12 and R13 surfaces are deeply textured, which makes them harder to clean, slower to install and less comfortable to walk on. In a hospital corridor, a texture that traps soil and resists disinfection can be a worse choice than a lower class with a disciplined cleaning regime.
The area decides the test, and the test decides the number. Working in the other direction — choosing a product and then looking for a room it suits — is how the wrong class ends up in a specification.
- Commercial kitchen. Shod staff, oil and grease. The relevant method is the shod ramp, and the specification should name DIN 51130 and a minimum class rather than a bare R number.
- Pool surround and wet rooms. Barefoot, wet, soapy. DIN 51097 A, B or C is the measure, with surface roughness as a check. An R class is not a substitute.
- Entrance lobby and retail. Shod, wet from weather, level. The pendulum is the usual measure, with a minimum PTV written into the specification.
- Healthcare. Mixed footwear and frequent wet cleaning, often with disinfectant residue that behaves like a lubricant. These areas frequently need two numbers, and the cleaning protocol is part of the specification.
- Ramps and slopes. The same product on a slope needs a higher class than on the level, and a floor that passes on the level can fail on a 1:12 ramp.
Construction also affects the answer: a rigid core product and a loose lay product can carry different surface textures and different joint profiles, so a class obtained on one does not transfer to the other. The range comparison in our SPC vs LVT guide covers the construction side; the SPC rigid core range page shows the formats available.
A slip classification describes a sample in a laboratory. A building is not a laboratory, and most slip incidents happen on floors that met their specification.
- The tested construction. The report names a thickness, a surface texture and a wear layer. A different build-up in the same family is a different product, and the class may not hold.
- Wear. Texture flattens with traffic, and a floor that measured well when new can drop a class after a few years of heavy use. This is one reason commercial specifications often over-specify by one class.
- Cleaning. Polish, high-alkaline residue and the wrong dose of detergent leave a film that behaves like the oil in the ramp test. The cleaning regime is a slip-control measure, not a housekeeping detail.
- Contamination beyond water. Water is rarely the worst contaminant in a real building; cooking oil, soap, food waste and cleaning chemicals are.
- Entrance matting. Most tracked-in water and grit arrives through the door, and adequate matting reduces the load on the floor itself more than a higher class does.
- Human factors. Footwear, load carrying, age, distraction and the direction of travel all change the risk in ways no classification captures.
The practical conclusion is the same one that applies to fire performance: ask for the report, check that it covers the construction being supplied, and treat the number as one input to the specification rather than the whole of it.
Is R11 more slip resistant than R10?
In the shod ramp test with oil, yes, because R11 covers a higher angle range. That does not make it more slip resistant in every situation. The R class says nothing about barefoot use or about clean water, and an R11 surface is more deeply textured, which can make it harder to clean and less comfortable underfoot. Match the test to the area before comparing classes.
Should a specification use an R class or a pendulum value?
Use whichever method matches the footwear and the contaminant in the area. Shod staff on oil point to the ramp; shod pedestrians on wet floors point to the pendulum; barefoot bathers point to the A, B, C classes. Some specifications ask for two methods for the same floor, which is reasonable in mixed-use buildings. What is not reasonable is treating the numbers as interchangeable.
Does a high R rating make a bathroom floor safer?
Not on its own. A bathroom is barefoot, wet and often soapy, which is the DIN 51097 condition. A high R class obtained with safety shoes on oil does not describe that condition, and the barefoot class plus a surface roughness figure is the relevant evidence. Ask for the test that matches the room, not for the highest number on the datasheet.
Specifying slip resistance for a project?
Send the area, the footwear, the contaminant and the destination market, and we will confirm which test the specification should name and what documentation to request for the construction being considered.
Request a B2B Quote ↗